Watering Timer
for 12V Battery Operation
IR/PV-02, 04,06, or 08  IrriGator Control  (Toro)

This is our 12V modified version of the popular Toro ECx Automatic Sprinkler System Timer. This timer has plug-in zone expansion modules. Each output expansion module operates two (or just one) valve solenoid. There is space for four modules, so the timer can be ordered with 2, 4, 6, or 8 zones. Yes, it works with all standard 24Vac solenoid valves, including existing, older sprinkler systems. Or can operate heavy loads via external relays. Useful for timing of deer feeders, lighting control, pump control, bird cage openers...anywhere ac power is not available. Timer runs on 12Vdc battery. Warranty 2 years. Our ordering numbers are:
Model No.
No. of
Zones
No. of Output
Modules
Price
IR/PV-02-XX
2
1
99.50
IR/PV-04-XX 4
2
114.50
IR/PV-06-XX 6
3
129.50
IR/PV-08-XX 8
4
144.50
IR/PV-02-MOD
Additional 2-Zone Expansion Output Module
15.00
Commercial irrigation timers including Hunter and Rainbird timers also available for 12Vdc battery operation. Note: Our modifications will void the mfr warranty. Return to CI  for warranty repair or exchange.
 

Timer shown with
two modules (four zones) installed


Timers are not easy to program! But, the ECx Timer is one of the more sensible. One can test it immediately after installation, by accepting the default watering time of 10 minutes per zone. To initially test the installation, just press the MANUAL switch twice then press NEXT to test the next zone, etc.  An optional wind or rain sensor can be connected to inhibit the zone outputs during these conditions. SAVES WATER.

Each zone output module connects to two valve solenoids. Typical wiring to solenoids is via #16 gauge direct-burial cable, sharing one common wire. 
   The timer has a Master Valve (MV) output that can be used to turn on a common valve,  such as a main line valve at a cistern. One application of this feature is to remove pressure from lightweight plastic distribution piping when all flow is stopped. The MV output is ON when any zone is ON.
   Alternatively,  a well water pump (solar?!) can be controlled using a power relay connected to these terminals. The pump relay coil should be rated at 12Vdc and draw less than 0.5A.

Typical  Smart Watering Timer for 12V Battery Operation
see  http://cisolar.com/catIrrigator2.html for other smart controls
Control Module Components - -   Toro TIS-612
1. Information Display

    Large, easy-to-read digital display provides text information for controller setup, programming and operating functions.

2. Upper Line Dial

    Turn this dial left or right to select the menu items that appear on the upper line of the display.

3. Lower Line Dial

    Turn this dial left or right to change the imput data that appears on the lower line of the display.

4. Copy Button

    The Copy button is prressed to execute the copy function  commmands

5. Function Dial

    Turn this dial left or right to select the various controller function.
    
Internal Controller Components
1. External Antenna Cable Receptacle Access Cover

2. Rain Sensor Bypass Switch - Enables the rain sensor ( if installed ) to be manually bypassed.

3. Safety Fuse - 2A slow-blow fuse protects controller transformer.

4. Valve Common Terminal - For connection of control valve and master valve/pump relay common wire ( if installed )

5. 24 VAC Terminal - For connection of  12V solar power (Was used for connecton of transformer wires).

6. Earth Ground Terminal - For connection of earth ground wires.

7. Station Valve Wire Connection Terminals - For connection of 24 VAC irrigation control valve power wires.

8. Master Valve/Pump Staqrt Relay Wire Connection Terminal.

9. Rain Sensor Connection Terminal - For Connection of a Toro rain sensor


Order from solar specialty dealers or directly from:

 CI Solar Supplies Co   PO Box 2805, Chino, CA 91710  USA  (909) 628-6440  jclothi@attglobal.net